QWinOut three225 FPV Racing Drone 225mm Wheelbase Quadcopter RTF with Radio Transmitter & Receiver F4 Betaflight Pro (V2) OSD/BEC Flight Controller 1200TVL Camera 2204-2300KV Motors BLHeli_32 ESC 5043 3-paddle Propeller
-
Detail
Product Name QWinOut three225 FPV Racing Drone 225mm Wheelbase Quadcopter RTF with Radio Transmitter & Receiver F4 Betaflight Pro (V2) OSD/BEC Flight Controller 1200TVL Camera 2204-2300KV Motors BLHeli_32 ESC 5043 3-paddle Propeller Item NO. F37491-J F37491-M F37491-K F37491-N Weight 1.22 kg = 2.6896 lb = 43.0342 oz Category DIY RC Drone Accessories> DIY RC Drone Kit Brand QWINOUT Creation Time 2020-09-09 QWinOut three225 FPV Racing Drone 225mm Wheelbase Quadcopter RTF with Radio Transmitter & Receiver F4 Betaflight Pro (V2) OSD/BEC Flight Controller 1200TVL Camera 2204-2300KV Motors BLHeli_32 ESC 5043 3-paddle Propeller
Functions and features
Built-in OSD Betaflight
Support BLHeliSuit configuration
Support voltage 2-3S
Paddle:
Model: 5043
Number of blades: 3 blades
Pitch: 4.3 inches
Material: PC
Weight/G: 4.63G
Inner diameter of center hole: 5mm
Paddle diameter: 13.5mm
Center thickness: 7mm
Maximum blade width: 15.58mm
ESC:
Project name: 35A ESC
MCU: STM32F051
Firmware: BLHeli_32 bit
Current: 35A
Size: 26x13x5mm / 1.01x0.51x0.20in
Weight: 7g / 0.25oz
Input voltage: 2-5s lithium battery
Support 500HZ PWM, Oneshot125, Oneshot42, Multishot, Dshot150/300/600/1200
Image transmission:
1. Input voltage: DC 7V-27V (2-6S)
2. Output voltage: DC 5V 2A
3. Power switching: five gears 25MW, 200MW, 400MW, 800MW, 1000MW
4. Signal channels: 40
5. Frequency point switching: manual button /IRC OSD (support at the same time)
6. Antenna interface: MMCX (distribution to SMA extension cable)
7. Dimensions: 36MM*36MM Pitch: 30.5*30.5MM, M3
Motor:
Model: 2204
Motor KV: 2300
Weight: 27 grams
Support voltage: 2-3S
Flight control:
Model: F4 (V2)
Support receiver functions: PPM, IBUS, SBUS, DSM
Built-in OSD
Installation hole distance: 30.5x30.5mm
Comes with BEC
Camera:
COMS image sensor: 1/3
Horizontal resolution: 1200 tvl
Lens: 2.1 mm
Signal system: PAL / NTSC
Power supply: DC 5 to 12V
Net weight: 5.0 g
Size: 19mm * 19mm * 19mm
Radio Transmitter:
Radio Transmitter & Receiver is Optional :
TX&RX for FLYSKY ; TX&RX for FRSKY
Optional 1: TX&RX for FLYSKY
FS-i6 FS I6 2.4G 6ch RC Transmitter Controller with FS-RX2A Pro Receiver
Optional 2: TX&RX for FRSKY
LiteRadio 2.4G 8CH 2 Radio Remote Controller Transmitter with Receiver compatible for FRSKY D8
-Supports Frsky protocol, easily change Frsky D8, Frsky D16 FCC and Frsky D16 LBT mode (The default version is Frsky D16 FCC)
-Built-in charging module, support USB charging
-Adopted the rubber coat and add weight, makes it more ergonomic
-Add vibration motor, provide a vibrating prompt
-Redesign the power button, make it crystal clear and better for the LED indication
Item: LiteRadio
Frequency Range: 2.4G (2403MHz-2447MHz)
2.4G System: NRF24L01 or CC2500
Channel: 8
System: Frsky Protocol
Power: 80mw
Model Type: Multi-rotor
Support USB Charging
Support FPV Simulator Connected
Output: PPM, support Student Radio Mode
LED Light: Green-Power On / Red-Warning / Blue-Normal
Battery: 350mAh 2S Battery
Weight: 227.4g (with battery)
How to change the protocol (D16/D8 Version):
To change FrSky protocols (FCC D16, EU D16, or D8), you first have to power it off, then press and hold the bind button while you power it back on. Then it will flash the code to indicate which protocol it is on.
LED Status - Protocol Version:
Flash Once - Frsky D16 FCC;
Flash Twice - Frsky D16 LBT;
Flash Three Times - Frsky D8
LiteRadio Guide
Manual for LiteRadio Radio Transmitter
LiteRadio Configuration - OpenTX Companion
Setup E.G. #1 - Trim the Gimbal Central Value
Battery & Charger is Optional :
no Battery& Charger; w/ Battery& Charger
11.1V 1500MAH 40C Lipo Battery with XT60 Plug with IMAX B3 PRO Compact 2S 3S Lipo Balance Battery Charger
Precautions:
1 Do not charge the battery when you are away from home, do not charge the battery immediately after flying, and do not over-discharge the battery (over-discharge may cause the battery to fail to charge and become useless).
2. Do not modify any parameters and wiring without knowing the flight control and remote control.
3. Turn on the remote control before powering on the airplane, unplug the power switch after the flight, and then turn off the remote control to prevent accidents.
4. This aircraft is recommended to fly indoors, and to fly in an open place outdoors when there is no wind, avoid flying in crowds and places with interferences around.
5. The product is unassembled/welded in loose parts. If you have any technical and assembly problems, please feel free to contact us. We have a dedicated technical team to answer related questions. If customers need to assemble, please feel free to contact us, we will give a reasonable quotation for additional logistics freight and technical assembly fees.
6. This product is not a toy and is not suitable for children under 14 years of age.
7. Please read the instructions carefully before any use. If you are a beginner, it is recommended to be assisted by an experienced adult
8. Because the airplane is relatively small, do not fly high and far away. 9. Novices should pay attention to not holding the airplane by hand or letting children to prevent it from being scratched.
10. Please turn off the start switch in time when the aircraft falls into a wall or hits other objects during flight, otherwise it may cause damage to the flight control motor, etc. Check whether the aircraft is damaged or the screws are loose. -
Customer ReviewsNo comments